Air Quality Doc No. HCD-map-combustion-sources-before-you-trust-the-alarm

Map Every Combustion Source Before You Trust the Alarm

A homeowner walk-through covers every fuel-burning appliance, its vent path, and the alarm itself before a technician arrives.

By The Dispatch Bench Desk: Air Quality
Home Comfort Dispatch

The furnace gets the attention whenever carbon monoxide comes up, but a house can produce it from more places than the heating appliance in the basement. In November, which is Carbon Monoxide Awareness Month, ACHR News ran Carbon Monoxide Safety Goes Beyond the Furnace, and its summary says contractors can help "uncover hidden risks" for homeowners. That same job belongs to you before the service call. A homeowner walk-through can find every combustion source, check how each one vents, and confirm the alarm is placed and working. It does not replace a technician's combustion test, but it takes an afternoon and tells you what to ask for.

List every combustion source

Start with a written list. Include the furnace or boiler, the water heater, a gas range and oven, a gas dryer, any gas or wood fireplace or stove, and any attached garage. Add anything with an engine, such as a generator, a snowblower, or a car that sits running in an attached garage. Portable heaters that burn fuel belong on the list too. Next to each entry, write how the appliance is vented and where the vent exits, because that is where most problems show up.

Read the vent path, not just the appliance

Follow each vent from the collar to the outside. Look for joints that have separated or were never fully seated, sections rusted through, connector screws that are missing, and loose or damaged pipe insulation along the run to the roof or wall. Soot or dark staining around a draft hood, flue collar, or pipe joint means you stop and call for service. At the top, check the termination for a bent cap, a screen packed with lint or debris, or a pipe placed too close to a window, soffit, or intake. Winter adds snow and ice to that list, since a drift can block an outlet without anyone noticing from inside the house.

Where a vent passes through the roof, the flashing is a roofing job, and a roofing contractor such as Keys Roofing can reseal that penetration. Pipe sizing, clearance, and draft belong to the heating side, so make sure the same person looks at both before the work closes up.

Test the draft with the house running as it normally runs

Draft problems often appear when the house is tight and every exhaust fan is running. Close the interior doors, run the bath fan and the kitchen range hood, and then, with the appliance firing, hold an incense stick or smoke pencil near the draft hood. The smoke should pull into the hood and rise up the vent. If it drifts into the room instead, the appliance is spilling exhaust, which is another stop-and-call finding. Never leave an open flame unattended while you run this test.

Keep your multimeter expectations realistic. A meter can confirm a 120-volt receptacle, a thermostat circuit, or a blower motor's current draw, but it does not measure carbon monoxide. That takes a sensor or an analyzer.

Check the alarm like any other piece of equipment

Alarms carry a manufacture date and a service life stated by the maker. Read the label, then replace the unit on that schedule rather than waiting for it to start chirping. Mount units where the manufacturer's instructions and your local code call for them, which usually means at least one on each level and near sleeping areas. Keep them out of the garage itself, away from direct airflow off the furnace, and out of bathrooms where steam can reach them. Press the test button monthly, and after any power outage, confirm the unit still responds. A battery-backed alarm is only as good as the battery someone remembers to change.

What to do if the alarm sounds

If an alarm goes off and you cannot identify a cause, get everyone outside into fresh air first. Then call the fire department or your local emergency number from outside the house. Do not go back in to hunt for the source. Before you leave, write down what was running at the time, because the responders will want to start there. A licensed technician can then run the combustion test, and you will hand over a list rather than a guess.

Bring the list to the service call

The walk-through list is your handoff. It names every appliance, its vent path, the condition you saw at each joint and termination, the draft result, and the alarm dates. A technician who receives that list can spend the visit on measurement instead of discovery, and you will have a record for the next time someone asks what is burning in your house.

← More from Air Quality