
A furnace or heat pump is rated for what it puts out at the equipment, but the house decides how much of that output it keeps. ACHR News has covered the Building HVAC Science podcast, which reached the quarterfinals of a national competition. The show's producer, Bill Spohn, has been releasing episodes since 2017, and the summary describes the subject matter as "building performance, HVAC technology, and industry best practices". That ordering matters. Building performance comes first, because a technician who has spent years on that topic tends to look at the shell before the box.
You do not need a blower door or a lab to borrow that habit. You need a flashlight, a thermometer that reads surface temperature, a stick of incense on a still day, and about an hour in the attic and the crawlspace. The goal is to find the places where conditioned air and outdoor air trade places without permission.
Start at the Attic Hatch
The attic floor is the boundary between your conditioned air and the weather. Look at the insulation depth first. Loose fill that sits below the joist tops across large areas tells you the coverage is thin, and a dark ring on the batts or blown fill often marks a spot where air is moving through the ceiling. Those dark rings are a good sign of air movement, not just dust.
Next, look at the penetrations. Plumbing stacks, wire bundles, bath fan housings, and the top of interior walls all make openings in the ceiling plane. Recessed can lights are the usual suspect. If a fixture is not rated airtight and sits under loose insulation, it can behave like a small chimney. Check the bath fan too. A fan that vents into the attic instead of outside adds moisture to the framing and can pull conditioned air up through the ceiling every time it runs.
Treat the Ducts as Part of the Envelope
Supply ducts in an unconditioned attic are the most overlooked heat loss in many homes. Check the joints where the trunk meets the plenum and where branch runs connect to the boots. Look for disconnected flex, crushed sections where the insulation has been pressed flat, and tape that has peeled away. A duct that has come loose from its boot can dump conditioned air straight into the attic while the room below stays a few degrees cold.
Run the system on fan or heat and walk the attic with an infrared thermometer. Compare the surface temperature of the duct with the air at the nearest supply register. A duct that reads close to attic temperature while the air coming out of the register is at supply temperature usually has a leak somewhere along that run, and a spot that feels far colder than the air inside it points to a seam worth sealing. Mastic and foil-backed tape are the normal fixes, and the tape should be the UL-listed kind rather than cloth duct tape. Do not seal anything near a flue or combustion appliance without a licensed technician looking at the venting first.
Find the Leaks at the Edges
The rim joist, where the floor framing sits on the foundation wall, is a common weak point in older homes. In a basement or crawlspace, look for gaps where the sill plate meets the masonry, unsealed penetrations for gas lines and cable, and foam that has shrunk or cracked. On a windy day, hold a lit incense stick a few inches from suspect spots and watch the smoke. Smoke that bends sharply toward a gap is showing you air movement. Keep the stick away from insulation and wood, use a holder, and put it out completely when you are done.
Check the return side as well. A return cabinet with a missing filter door or an unsealed panel can pull unfiltered air from the garage or the crawlspace into the system, and that air carries moisture and cold with it. Pressure differences between rooms also matter here. If a closed bedroom door changes how the house feels, the return and supply balance may be off, and that is a question for a technician with a manometer.
Keep the Schedule Honest
A thermostat schedule only works if the envelope holds the setback. A house that loses heat fast will recover slowly from a night setback, and the equipment will run longer to catch up. Before you blame the controls, run a simple test: set the thermostat to a steady temperature for a day, then note how long the house takes to drop a few degrees after the heat stops. A long, slow decline tells you the shell is holding heat well. A quick drop tells you the leaks found above and below are worth fixing first.
For an older relative who lives alone, a house that holds its heat is a safety matter, and families sometimes arrange non-medical in-home support for older adults in St. Louis to check the thermostat, confirm the house is at a comfortable temperature, and make sure a space heater is not sitting against curtains. Those are household checks, not medical ones, and they should stay with the family and the equipment technician who maintains the system.
Start small. One afternoon in the attic, one smoke test along the rim, and one duct check will tell you more about your house than any generic energy tip. The equipment matters, but the shell decides whether the equipment gets to finish the job.